GRiSO ghetto
Would you like to react to this message? Create an account in a few clicks or log in to continue.


12425 - Established June, 2013 - all GRiSO, all the time...
 
HomeRegisterLog in

 

 Valve lash flat v roller

Go down 
2 posters
AuthorMessage
Omnis
GRiSO Capo
GRiSO Capo
Omnis


Posts : 277
Join date : 2014-10-07

Valve lash flat v roller Empty
PostSubject: Valve lash flat v roller   Valve lash flat v roller Icon_minitime1Mon May 30, 2016 6:29 am

Apologies if it has been answered before :
on flat tappets valve lash was set at 0.10 (4 thou) inlet and 0.15 (6 thou) exhaust. Are these tolerances the same for the roller tappets? I seem to recall 0.15 and 0.20 respectively mentioned somewhere.
Many thanks
Back to top Go down
beetle
GRiSO Capo
GRiSO Capo
beetle


Posts : 10029
Join date : 2013-10-01

Valve lash flat v roller Empty
PostSubject: Re: Valve lash flat v roller   Valve lash flat v roller Icon_minitime1Mon May 30, 2016 6:39 am

0.1 & 0.15 were the original factory clearances for flatties. They recommend 0.15 & 0.20 for flat tappets at some point in an attempt to increase tappet life. Rollers should be 0.1 & 0.15.




.

--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
.


.
[You must be registered and logged in to see this image.]
.
In GRiSO we trust!
.
Back to top Go down
https://www.griso.org
Omnis
GRiSO Capo
GRiSO Capo
Omnis


Posts : 277
Join date : 2014-10-07

Valve lash flat v roller Empty
PostSubject: Re: Valve lash flat v roller   Valve lash flat v roller Icon_minitime1Mon May 30, 2016 6:45 am

Thanks Beetle, that's what I have set my rollers to. Just back from England armed wth Carbtune.
This morning checked valves, synced TB, Guzzidiaged it, loaded Beetle map, went on a 200kms burn up.
That beautiful Tenni beast sang like a canary and went like wind tail of hell. Simply AWESOME.
Thanks for your efforts with the maps.
Back to top Go down
beetle
GRiSO Capo
GRiSO Capo
beetle


Posts : 10029
Join date : 2013-10-01

Valve lash flat v roller Empty
PostSubject: Re: Valve lash flat v roller   Valve lash flat v roller Icon_minitime1Mon May 30, 2016 6:48 am

cheers

--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
.


.
[You must be registered and logged in to see this image.]
.
In GRiSO we trust!
.
Back to top Go down
https://www.griso.org
Sponsored content





Valve lash flat v roller Empty
PostSubject: Re: Valve lash flat v roller   Valve lash flat v roller Icon_minitime1

Back to top Go down
 
Valve lash flat v roller
Back to top 
Page 1 of 1
 Similar topics
-
» Roller vs flat tappets on a 2013
» 8 Valve roller lifters
» Valve setting 4 & 6 or 6 & 8 for a roller?
» Serial #s and Flat Tappets
» Flat Tappets and Roller Tappets

Permissions in this forum:You cannot reply to topics in this forum
GRiSO ghetto :: The Ghetto :: GRiSOLOGY-
Jump to: