| oil pressure | |
|
+3Pete Roper Kiwi_Roy mike 850T 7 posters |
Author | Message |
---|
mike 850T GRiSO Capo
Posts : 12 Join date : 2015-08-10
| Subject: oil pressure Thu Jun 13, 2019 10:59 pm | |
| I just bought an 1100 with 17,000kms on the klock and put an oil guage on it oil pressur hot is at tickkover 1bar(14psi) at 3000rpm 3-4 bar not seen more than 4 bar (hot or cold). my 850(84,000kms) with new oil(10w60 synth.) at tickover 2-3bar and 3000rpm arround 5 bar. I will change the oil on the 1100er but my question is what`s the right setting for the oil pressure release valve? [You must be registered and logged in to see this image.]pics are the 850 motor Thanks mike | |
|
| |
Kiwi_Roy Nibbio
Posts : 519 Join date : 2017-11-10
| Subject: Re: oil pressure Fri Jun 14, 2019 3:47 pm | |
| 4 Bar (60 psi) sounds about right, that's what my other Guzzis run at, a 6 Bar (100 psi gauge) is about right. 1 Bar (15 psi) at idle when hot but should go back to 4 with some revs on. You shouldn't touch the oil pressure relief, it will be fine.
Last edited by Kiwi_Roy on Fri Jun 28, 2019 4:03 am; edited 5 times in total | |
|
| |
mike 850T GRiSO Capo
Posts : 12 Join date : 2015-08-10
| Subject: Re: oil pressure Fri Jun 14, 2019 5:22 pm | |
| Thanks Roy, done 160kms/100mile on is today goes like hell 200+kmh. sounds like a tracktor,much louder than the 850 oil pressure around 4 bar : I did´nt think there would be such a difference in the two GRiSO motors sounds like a tracktor,much louder than the cultured 850 maybe i should try the 1200 [You must be registered and logged in to see this image.] | |
|
| |
Pete Roper GRiSO Capo
Posts : 10665 Join date : 2013-05-30 Age : 67
| Subject: Re: oil pressure Fri Jun 14, 2019 10:35 pm | |
| If you think it's too low the most likely culprit will be the gasket between the sump spacer and the block but this is not something I've seen on an 1100. If it were to occur I'd expect it to be more likely to be a problem with the later models with the trochoidal pump. | |
|
| |
Street L'Innominato
Posts : 3412 Join date : 2013-05-30 Age : 65
| Subject: Re: oil pressure Sat Jun 15, 2019 12:49 am | |
| Mike, I like this geegaw, t'would look nice with my other red accents. Where did you find that one? Pete (Street) [You must be registered and logged in to see this image.]--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- [You must be registered and logged in to see this image.]“Danger + Survival = Fun.” - Neil Peart[You must be registered and logged in to see this link.] | |
|
| |
mike 850T GRiSO Capo
Posts : 12 Join date : 2015-08-10
| Subject: Re: oil pressure Sat Jun 15, 2019 8:19 am | |
| morning Pete (Street),I was lucky it came with the bike. geegae | |
|
| |
Street L'Innominato
Posts : 3412 Join date : 2013-05-30 Age : 65
| Subject: Re: oil pressure Sun Jun 16, 2019 6:02 am | |
| Thanks, Mike, better add that to my xmas list. --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- [You must be registered and logged in to see this image.]“Danger + Survival = Fun.” - Neil Peart[You must be registered and logged in to see this link.] | |
|
| |
2highlander Biondino
Posts : 244 Join date : 2016-09-28 Age : 64
| Subject: Re: oil pressure Sun Jun 16, 2019 8:08 am | |
| It is either from Roland Däs or KC34.com ... | |
|
| |
eeyore Grignapoco
Posts : 189 Join date : 2016-09-09
| Subject: Re: oil pressure Sun Jun 16, 2019 7:07 pm | |
| Double digits (psi) at idle is fine. | |
|
| |
moto Grignapoco
Posts : 181 Join date : 2014-07-03
| Subject: Re: oil pressure Thu Jun 20, 2019 2:48 am | |
| Mike,
That looks like a nice oil pressure gauge and a clean installation. May I ask what model of gauge it is, and where you got it?
Thanks,
Moto
| |
|
| |
mike 850T GRiSO Capo
Posts : 12 Join date : 2015-08-10
| Subject: Re: oil pressure Mon Jul 29, 2019 7:28 pm | |
| I bought it at a local hydraulik shop pressureguage GMM50H , you might get one at your local Harley dealer but ask for guage with 0 - 80 psi. with stainless steel housing,I taped into the oil supply to the cylinder head . beets the sevice warning you get now and then, in the rain. sorry its late holliday in the UK. | |
|
| |
moto Grignapoco
Posts : 181 Join date : 2014-07-03
| Subject: Re: oil pressure Sat Aug 03, 2019 3:16 am | |
| Mike,
Thanks! That steel housing seems to be hard to find on gauges. I may check at the Harley dealer as you suggested.
Moto
| |
|
| |
Sponsored content
| Subject: Re: oil pressure | |
| |
|
| |
| oil pressure | |
|